Tips For Printer Using Infus Ink

There are so many who come to the store computer service for complaints with this one product.
Actually installed on the printer ink infusion with the aim to reduce the cost of printer ink. Because the original ink is quite expensive.
Ink infusion it is a tube with an additional ink is placed on the outside of the printer and supplied into the printer through the IV. Hose mounted on the Canon brand printers are always inserted into the original cartridge. As with the Printer Brand Epson, a hose mounted on a cartridge that is not the original. hose consists of 4 colors, or some types of printers such as Epson R230 hose there are 7 colors.
If you rarely use the printer (say once a week, or once a month) I suggest you not to install the ink infusion. Because the ink infusion usually have problems at a pressure hose, due to differences with the outside air pressure if left long enough will cause the ink drop (air bubbles appear on the hose). And also on the printer head will be quickly damaged, due to which there is always a puddle of ink on the printer head gap. This arises because the ink puddle always contains a full ink cartridge. So you should just use the ink type of injection because head will be more durable.
Note also with your warranty. Printer that has infused the guarantee no longer exists, because the infusion of the printer is ink which is not native of the printer that you buy the product. Infusion is a modification of printer ink which incidentally is not legalized by the printer manufacturers. So it is better if you spend menginfus first new original printer ink.
Well, if you still want your printer menginfus then consider the following suggestions for the printer you are still preserved there:
1. Put the infusion tube is parallel with your printer head. It is intended that the suction pressure of the printer head that takes the ink is not too difficult or not too easy (Balanced). If there is air bubbles in the hose just use the facility "cleaning" of your printer software. Then vacuum the ink had to be replenished. If after cleaning the ink was still not up, then note the hose if there is a leak, or elbow there is a broken / cracked, or rubber also suffered torn elbow. If the hose is torn, try patched hole. If elbow broken, then replace with a new elbow. Or torn rubber also replace with a new one. One thing to note, too, when you lift it high infusion tube then it is a mistake, because a lot will be filled into the ink cartridge and will cause the ink to the printer head overflow. While repairing a hose or elbow please tie first with a rubber hose or duct tape the ink from spilling everywhere.
2. If print quality is not satisfactory, try the print nozzle check. Note whether the ink can go all out or not. Try to do cleaning once or twice. If there is ink that does not appear it's likely there is a blockage in your printer head gap. The fix is:- Tie the hose before the ink from spilling.- Disconnect the hose and elbow of printer cartridges.- Take a piece of tissue and try to stick on the head several times until the ink appears ditissue.- If the ink still does not show-up try to take an injection with an injection of air and exhale through the hole slowly until the ink cartridge out.- When the ink can come out smoothly, but does not appear when printing, then pumping the ink inside the cartridge that is problematic. In this new cartridge must be replaced, because it can not be repaired. This is because the design of the cartridge is sealed with a printer head. When it is opened then closed it again when there will be a gap that resulted in infusion of air into the tube so it will not work normally.- When you have finished making your infusion services, reattach the hose properly, do not get the hose caught on when the printer is used.
3. If this is your first time using ink infusion, then a time will appear an error message that you can not print the result. This is normal, because the cartridge was designed by the manufacturer, an extra prints. The solution is to press and hold the resume button on your printer for 5 seconds. Then the printer will return to print as usual. The purpose of pressing the reset button, is to ignore the error message ink runs out.
4. Do not be surprised if you find that the status of ink in your computer becomes empty after a long time, but you are still a lot of ink infusion. Thisbecause the monitoring system is based on ink cartridge counter the printed paper. Not based on monitoring the number of ink cartridges. So just let the status of your ink is empty existence, yet you can still print.
5. Do not do cleaning too often, because it will result in full on the printer waste ink reservoir. It is usually characterized by the presence of errors Absorber Full. If your printer absorber full, then you should replace your absorbers with a new printer or ink drying exhaust manually, by unpacking your printer. Printer ink absorber in the form of a sponge-shaped beam length and is connected by a hose printer ink. If you have your printer serviced absorber, the printer is also still displays the error message. The solution is to reset counter absorber your printer. For the type of Canon iP1980, iP1880, IP1700, IP1300, IP1200, how to reset absorber as follows:- Turn off your printer first (Power Off)- Unplug the power on- Press and hold the power on- While holding down the power on, plug the power cable back.- While holding down the power on, press the resume button 2x- Disconnect the power on button- Turn the printer- The absorber settings your printer will return 0
6. Always close your re-infusion after using the printer. It is intended that the ink does not flow slowly into the cartridge (ink Locking)
In conclusion, using the ink infusion is very risky to your printer, but if you understand how to use IV then ink your printer will be durable, and can be used on.